If needed, consult a Sony dealer or a licensed contractor for wall reinforcement information. If the wall strength is insufficient, make sure it's reinforced before installation.On your TV model page for the Wall-Mount Bracket installation information. For more details about required wall strength, check the The wall where you plan to mount your TV must have the strength to withstand 4 times (6 times in some models) the weight of your TV.The wall mount hole pattern on some models may conform to the VESA Mount Standard, but the number and depth of the screw holes do not. WARNING! If you use screws other than those specifically supplied with the wall mount bracket for your TV, the TV may fall and cause physical injury to someone or damage to the TV. Make sure to use the proper size and length of screws specified for your TV. Use the screws supplied with the wall-mount bracket specified for your TV when attaching your mount. Information about the screws, screw hole patterns, and measurements We don't guarantee the use of third-party wall mount brackets or screws.For safety reasons, and to make sure the installation is performed correctly, follow the wall-mount bracket instruction manual, the TV Setup Guide, and the instructions in this article.Manuals are posted on your model support page. Check the wall-mount installation manual supplied with your TV for more information about the strength of the wall.Contact your local retailer or local custom installer to assist with this installation.The wall must have the strength to withstand four times (six times in some models) the weight of the TV. For safety and product protection, we recommend that a qualified professional perform the installation of your TV on the wall.WARNING! If you use substitute items other than the supplied screws, the TV may fall and cause physical injury to someone or damage to the internal parts of the TV. We're not liable for any damages or injury caused by mishandling or improper installation of the wall-mount bracket. WARNING! There's a risk of damage to your TV if you don't follow the installation instructions correctly. A wheel with 5 lugs on a 5.5" circle has a 5 x 5.5" bolt pattern.This article provides basic information for mounting your TV to a wall using a wall mount bracket, the screw hole pattern (distance between screw holes), the length of the power cord, and the weight of the TV without the stand. The pattern is measured in inches or millimeters and is displayed as the number of lugs times the diameter of the circle. Hub-centric wheels normally use flange style lug nut.īolt Pattern: The quantity and pattern in which the wheel's lug nut holes are laid out is referred to as the wheel's bolt pattern. Hub-Centric: Wheels that support the weight of the vehicle on the axle hub flange are hub-centric and require a center bore that offers an exact fit. Lug-centric wheels require tapered or ball style lug nuts. Lug-Centric: Wheels that place the weight of the vehicle on the lug nuts are called lug-centric and require a center bore that is simply large enough to clear the axle hub. It is measured in millimeters and is often abbreviated as "CB". Offset is also sometimes listed as ET with ET45 being a 45mm offset.Ĭenter Bore: The size of the hole in the center of a wheel is known as the center bore. A negative offset wheel sits outward while a positive offset wheel sits further inward. It is measured in millimeters from the centerline of the wheel to the wheel mounting surface. Offset: Offset is similar to backspacing in that it determines how far out from the axle the wheel will sit. It wil only print the size you set for I.D and O.D. Videodummy: I stretch it until it is barely bigger than the template. Just make sure to center the drawing on the template. Backspacing is often abbreviated as "BS" and measured in inches. and 116-118 O.D., regular printables are approx. This measurement determines how far out from the axle the wheel will sit and is a critical dimension for proper wheel fitting. A wheel with a 17" diameter and 8.5" width would be listed as a 17 x 8.5" wheel.īackspacing: The distance from the back of the wheel to the wheel mounting surface is called backspacing. Wheel Size: Wheels are sized according to their diameter and width measured from the tire mounting surfaces, usually in inches.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |